Product Range > Machine & Machine tools > Single Shot Oil > Motorised Pumps
MOTORISED PUMPS
MODEL LUB PACK - 3003 - PS - FS
  • This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump.

  • The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.

  • Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level).

  • During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 25-28 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.

  • During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.

  • The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.

  • For vertical mounting of the unit, two holes are provided at the back of the system.

  • There is an inbuilt check valve and pressure reducing system incorporated in the pump.

  • Outlet port is suitable for 6mm OD tube.

cenlub
Discharge of Pump : 350 cc / min.
Reservoir Capacity : 3.0 ltrs. (in polycarbonate material)
Motor : 0.09 KW, 1500 rpm, 3 Phase, 415 V
Relief Valve : Pre set at 20 kg/sq.cm.
Pressure Switch : 42 V (Max), 0.2 Amp (Max), Pre set at 18kg/sq. cm, 1 NO + 1 NC contact.
Float Switch : 42 V (Max.) 0.2 Amp (Max.), 1 NC contact (oil filled)
Suitable oil Viscosity : Between 32 to 460 cSt / 40 degrees celcius


MODEL LUB PACK - 3003 - PS - FS -AL
 
  • This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump.

  • The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.

  • Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level).

  • During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable at 28 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.

  • During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.

  • The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.

  • For vertical mounting of the unit, two holes are provided at the back of the system.

  • There is an inbuilt check valve and pressure reducing system incorporated in the pump.

  • Outlet port is suitable for 6mm OD tube.

cenlub
Discharge of Pump : 350 cc / min.
Reservoir Capacity : 3.0 ltrs. (in die cast Aluminium material)
Motor : 0.09 KW, 1500 rpm, 3 Phase, 415 V
Relief Valve : Pre set at 25 kg/sq.cm.
Pressure Switch : 220 V (Max), 0.1 Amp (Max), Pre set at 20kg/sq. cm, with 1 NO + 1 NC contact.
Float Switch : 42 V (Max.) 0.2 Amp (Max.), 1 NC contact (oil filled)
Suitable oil Viscosity : Between 32 to 460 cSt / 40 degrees celcius


Mini Motorised Lubrication Unit MODEL AR-AMGP-01S
 
  • This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump.

  • The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.

  • Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level).

  • During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.

  • During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.

  • The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.

  • For vertical mounting of the unit, two holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump.

  • Unit is supplied with an adoptor (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6mm OD tube.

cenlub
Discharge of Pump : 150 cc / min.
Reservoir Capacity : 1.8 ltr in polycarbonate material
Motor : 25 W, Single Phase, 220 V / 110 V
Relief Valve : Pre set at 15 kg/sq.cm.
Pressure Switch : (optional)
Digital Timer : (optional)
Float Switch : (optional)
Suitable oil Viscosity : Between 32 to 460 cSt / 40 degrees celcius


Motorized Lubrication Unit MODEL AR-AMGP-200NS
 
  • This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump.

  • The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.

  • Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level).

  • During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.

  • During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.

  • The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.

  • For vertical mounting of the unit, two holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump.

  • Unit is supplied with an adoptor (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6mm OD tube.

cenlub
Discharge of Pump : 250 cc / min.
Reservoir Capacity : 3.0 ltrs. in Polycarbonate Material
Motor : 40 W, Single Phase, 110 / 220 V
Relief Valve : Pre set at 20 kg/sq.cm.
Pressure Switch : Built in
Float Switch : Built in
Suitable oil Viscosity : Between 32 to 680 cSt / 40 degrees celcius


Motorised Lubrication Unit MODEL ALU-03 LG
 
  • This is a mini hydraulic power pack fitted with a motor and rotary positive displacement pump.

  • The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.

  • Unit is fitted with a suitable pressure switch, float switch and oil window for checking oil level.

  • During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.

  • During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.

  • The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.

  • For vertical mounting of the unit, four holes are provided at the back of the system. There is an in-built check valve and pressure reducing system incorporated in the pump.

  • Unit is supplied with an adoptor (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6mm OD tube.

  • The unit is fitted with electrical contactor and timer. 3 phase electrical line to be given to a terminal strip fitted with the lubrication unit. Timer and motors controls thus are on the lubrication reservoir of the lubrication unit 10 metering cartridges of 0.16 cc are fitted, which are ready to feed oil to the lubrication points.

  • The unit is suitable for liquid grease or high viscose oil. The unit is fitted with an S.S. reservoir of 3 ltr. capacity at the bottom.

  • There is a small 220 V gear motor fitted at the bottom of the reservoir to facilitate churning of liquid grease.

cenlub
Discharge of Pump : 0.5 L.P.M.
Reservoir Capacity : 3.0 ltrs.
Motor : 0.09 KW, 1500 rpm, 3 Phase, 415 V
Relief Valve : Pre set at 15 kg/sq.cm.
Pressure Switch : 42 V (Max), 0.2 Amp (Max), Pre set at 12kg/sq. cm 1 No. contact.
Float Switch : 42 V (Max.) 0.2 Amp (Max.), No contact.
Suitable oil Viscosity : 1000 cst


Motorised Lubrication Unit MODEL ELU-2700
 
  • This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump.

  • The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.

  • Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level).

  • During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.

  • During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.

  • The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.

  • For vertical mounting of the unit, two holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump.

  • Unit is supplied with an adoptor (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6mm OD tube.

cenlub
Discharge of Pump : 0.5 L.P.M.
Reservoir Capacity : 3.0 ltrs.
Motor : 0.09 KW, 1500 rpm, 3 Phase, 415 V
Relief Valve : Pre set at 15 kg/sq.cm.
Pressure Switch : 42 V (Max), 0.2 Amp (Max), Pre set at 12kg/sq. cm 1 No. contact.
Float Switch : 42 V (Max.) 0.2 Amp (Max.), No contact.
Suitable oil Viscosity : 1000 cst


Motorised Lubrication Unit MODEL ALU-03
 
  • This is a mini hydraulic power pack fitted with a motor and rotary positive displacement pump.

  • The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.

  • Unit is fitted with a suitable pressure switch, float switch and oil window for checking oil level.

  • During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, for safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.

  • During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.

  • The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.

  • For vertical mounting of the unit, four holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump.

  • Unit is supplied with an adoptor (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6mm OD tube.

cenlub
Discharge of Pump : 1 L.P.M.
Reservoir Capacity : 2.7 ltrs.
Motor : 0.09 KW, 1500 rpm, 3 Phase, 415 V
Relief Valve : Pre set at 15 kg/sq.cm.
Pressure Switch : 42 V (Max), 0.2 Amp (Max), Pre set at 12kg/sq. cm 1 No. contact.
Float Switch : 42 V (Max.) 0.2 Amp (Max.), No contact.
Suitable oil Viscosity : Between 32 to 220 cst/40c


Motorised Lubrication Unit MODEL ALU-CEN-03 CE
 
  • This is a mini hydraulic power pack fitted with a motor and rotary positive displacement pump.

  • The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.

  • Unit is fitted with a suitable pressure switch, float switch and oil window for checking oil level.

  • During ON cycle, (5 sec. fixed), the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, for safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.

  • During OFF cycle (any time more than 2 minutes -adjustable) the pressure in the lubrication line isreduced to 1 kg/sq.cm. and so on.

  • The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.

  • For vertical mounting of the unit, four holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump.

  • Unit is supplied with an adoptor (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6mm OD tube.

cenlub
Discharge of Pump : 1 L.P.M.
Reservoir Capacity : 3.0 ltrs.
Motor : 0.12 KW, 3 phase, 4 pole, 415 V, 50 Hz
Relief Valve : Pre set at 15 kg/sq.cm.
Pressure Switch (CE) : 24 V (Max), 0.1 A (Max), Pre-Set at 12 kg/cm2 1NO Contact
Float Switch : 42 V(Max), 0.1 A (Max) (Vertical reed type)
Pressure gauge : 0-25 kg/cm2
Suitable oil Viscosity : Between 32 to 220 cst/40c